Произвођач славина ВИГА 
Faucets are divided into basin faucets, Плусни туширања, thermostatic faucets, итд. The maintenance methods of these different types of faucets are also slightly different.
Basin Faucet
When buying a single-handle basin faucet, you should pay attention to the diameter of the outlet. Except for TOTO basins, most of them are national standard products on the market. Most of GROHE’s basin faucets are hard pipe water inlets, so you should pay attention to the height of the upper nozzle, 35 working points** from the basin down is appropriate. Током инсталације, an angle valve dedicated to Grohe must be selected, а угаони вентил мора бити причвршћен на цеви за топлу и хладну воду са зида. Када установите да постоји размак између угаоног вентила и водоводне цеви на славини, go to your store at the time to purchase a special extension pipe for the GROHE faucet to connect it.
Сетити се, не смете користити друге водоводне цеви за повезивање, јер ако је притисак воде висок, лако ће отпасти и пропуштати воду, узрокујући вам губитак. Ако је улазна цев предугачка да би премашила излазну цев, the part can be cut off according to your needs. Ако угао није одговарајући, you can bend it to the position you need. Сетити се: Don’t bend to 90 degrees or greater than hard. When installing the basin to drain, please do not forget to purchase the small connector of the faucet (short-circuit the faucet).
Туш, Славина за каду (wall hanging)
After you buy a shower, кабл, or wall-mounted faucet, you can choose a suitable height to bury the water pipe. The distance between the hot and cold water pipes must reach 15 work points. You must not forget to flush the water pipe before installation to avoid excessive water quality and damage to the faucet. If the elbow between the faucet and the wall joint is too long, you can cut off a part of the 4-point wire. Сетити се: the 6-point wire connected to the faucet does not seem to be cut randomly.
Скривен туш, Славина за каду
Након куповине скривене славине, језгро вентила славине је углавном претходно закопано у зид. Be sure to pay attention to the thickness of the bathroom wall before embedding. Ако је зид превише танак, the spool cannot be embedded. Do not remove the plastic protective cover of the valve core easily when embedding, so as not to damage the valve core due to cement and other chores. Поред тога, you should pay attention to the up and down, left and right directions of the spool when embedding the spool to avoid the wrong spool.
Shower faucet
After you install the shower and bathtub faucets, don’t forget the filter in the shower pipe when you need to install the shower. When installing the shower, the water pressure must not be too high, generally 1&mDASh;—3 kg is the best, not more than 5 кг. If the water pressure is too high, the water flow restrictor in the valve core of the faucet can also be opened to reduce the water pressure, which can also achieve the effect of water saving.
Термостатска славина
Before installing the thermostatic faucet, please check whether the water pipe is hot on the left and cold on the right. Remember not to connect the hot and cold water pipes wrongly to prevent the faucet from not working properly. Gas and solar water heaters cannot use thermostatic faucets because the water pressure is too low. Don’t forget to install the hot and cold water filter when installing the thermostatic faucet.
Daily maintenance
In the process of using the faucet, it is necessary to frequently maintain and clean the scale on the surface of the faucet and the water sand in the spout to protect the chrome layer on the surface of the faucet as bright as new (GROHE special cleaning fluid, special cleaning cloth). Do not use rough towels and cloths to wipe the faucet, so as not to scratch the chrome layer, and do not touch the faucet with acid-alkaline items to avoid destroying its brightness.