VIGA水龙头制造商 
“Why did I replace the entire faucet and it was still leaking? There is a problem with your faucet! I want to return it!!” Losing money, losing money, losing money, important things are said three times, all kinds of complaints require compensation! Many times, the bathroom terminal The sales store is also very wrong. I am a regular specialty store. Why should there be any problems?
实际上, sometimes the water leakage of the faucet has nothing to do with the faucet itself. It may be caused by improper installation of the water hose and the faucet body. 此外, it may also be caused by problems such as aging, unstable water pressure or corrosion of the water supply hose that supplies water to the faucet. Once the water hose is cracked or burst, the consequences will be serious. 所以, experts recommend checking or replacing the water hose every 1-2 年.
Why does the faucet leak?
Most people think that the faucet leakage is a problem with the valve core. 实际上, as long as the valve core is used properly, the valve core is not prone to problems. 所以, if the faucet leaks, it should be analyzed from its essence.
— 【1 】—Water will drip after the new faucet is closed
After the new faucet is closed, dripping will appear. In such a situation, most owners will think that this is a problem with the faucet valve core. 实际上, the water dripping for a few seconds after the new faucet is closed is caused by the remaining water in the cavity after the faucet is closed. This is normal. But if the water is ticking for a long time, it is a faucet problem.
— 【2 】—Poor water quality
Many people don’t understand, what is the relationship between poor water quality and a leaking faucet? 实际上, poor water quality will cause trash to accumulate in the valve core, which can easily cause the valve core to not close tightly.
— 【3 】—Scratch on tap spool
使用过程中, the valve core is scratched due to the abrasion of foreign hard materials. 例如, when the water supply pipe is broken and the water is re-emerged, the water may contain rust or sand particles, which may cause the surface of the valve core to be scratched during the opening and closing process. Sealed and leaking. 所以, when installing the faucet, be sure to clean up the impurities in the water pipe.
— 【4 】—Pipeline connection
The water inlet hose and the main body of the faucet leaked due to improper installation.
Uncover the cause of the leaking faucet and prescribe the right medicine!
— 【1 】—The faucet still leaks water after the valve core is closed
This phenomenon may be caused by the loosening of the pressure cap causing the valve core to become loose and unable to seal the water. The solution is to remove the handle and decorative cover, and tighten the pressure cap again. Another possibility is that the rubber ring at the bottom of the valve core is deformed. Can not seal the water, the solution is to take out the valve core, check the bottom rubber ring, reset it and reinstall it.
— 【2 】—Water seeps from around the valve core
This phenomenon may be that the spool is loose or displaced. The solution is to remove the spool and install it again.
— 【3 】—Water seeps from the middle part of the valve core
This phenomenon is that the valve core is damaged. The solution is to replace the valve core. If the faucet leaks, replace the valve core, which will inevitably increase maintenance costs.
— 【4 】—Water leakage at the bottom of the faucet
This phenomenon is generally caused by the O-ring of the water inlet pipe not being installed or deformed. The solution is to unscrew the hose. If the O-ring is not deformed, re-fit the O-ring and the water inlet pipe. 是的, if you find that the O-ring has been deformed, replace the O-ring.
What should I do if the faucet leaks?
— 【1 】—The push-type faucet leaks
步 1. 关闭进水阀. 拧下水龙头手柄上或后面的小螺丝，即可取下固定在水龙头本体上的手柄. 一些螺丝隐藏在金属按钮下面, 塑料按钮, 或塑料片, 卡入或旋入手柄. 只要你打开按钮, 你会看到顶部的手柄螺丝.
步 2: 拆下手柄并检查水龙头的部件. 使用大滑动接头钳或活动扳手拆下填密螺母, 小心不要刮伤金属. 按照与打开水龙头时相同的方向转动阀芯或轴以将其拧开.
步 3: Remove the screws holding the washer. 如有必要, 使用渗透性润滑剂松开螺丝. 检查螺钉和阀芯, 如果损坏则予以更换.
步 4: 用相同的新垫圈更换旧垫圈. 新垫圈与旧垫圈几乎完全匹配，通常可以防止水龙头滴水. 还应注意旧垫圈是否有斜面或平面, 并更换相同的新垫圈. 专为冷水设计的垫圈在热水流过时会剧烈膨胀, 堵塞出水口，减缓热水流速. 有些垫圈可以在热水和冷水中工作, 但您应该确保您购买的替换垫圈与原始垫圈完全相同.
步 5: 将新垫圈固定到阀芯上, 然后将零件重新安装到水龙头中. 顺时针旋转线轴. 线轴就位后, 重新安装填料螺母. 小心不要用扳手刮伤金属.
步 6: 重新安装手柄并将按钮或圆盘装回. 再次打开供水并检查是否漏水.
— 【2 】—Water tap leakage caused by the sealing ring of the tap
关闭水龙头时出现滴水现象; 当水流过水龙头时就会发生漏水. 如果您看到水从手柄周围涌出, 你的水龙头漏水了; the first thing to do is to make sure the packing nut of the faucet is tight, but be careful not to scratch the nut with pliers or wrench.
如果发现漏水的原因不是螺母松动, 那么你需要更换密封圈. 水龙头的密封圈可以是由一个或多个O型橡胶圈组成的紧密密封圈, 或者它可以是类似绳子或软金属线的东西，缠绕在填料螺母下的阀芯上.
— 【3 】—Water leakage caused by valve seat of faucet
如果更换垫圈后水龙头仍然滴水, 那么可能是水龙头的阀座有问题. 垫圈损坏可能会导致水龙头阀座被金属阀芯磨损而变得凹凸不平, or the deposition of chemical substances in the water may form a residue, 防止垫圈与阀座完全压缩.
Steps: 将阀座紧固扳手插入阀座, 然后逆时针转动. 拆下旧阀座后, 确保您购买的新阀座与原始阀座完全相同. 如果座椅无法拆卸, 插入一个座套，该座套可以滑入旧座椅的适当位置并提供密封. 两种类型的阀座滚轮或打磨机可以压平磨损的阀座.
— [4]—The O-ring of the faucet causes the faucet to leak
厨房的水龙头有一个或多个O型圈，以防止水从出水口周围涌出. 如果 O 形圈磨损, 每次打开水龙头都会看到水从出水口底部流出.
步 1: 关闭供水, 逆时针旋转并拆下固定出水口的螺纹连接螺母. 一定要用胶带将螺母包裹起来，防止被钳子或扳手划伤.
步 2: 拆下连接螺母后, 将出水口向上提起，从出水座上取出. 你可以在出水座上看到这些环.
步 3: 将有问题的戒指更换为相同尺寸的新戒指. 重新组装水龙头.
What aspects should be paid attention to in the faucet?
◆What should be paid attention to when repairing water tap leaking?
If you repair it yourself, the first thing is to turn off the water supply. Just turn off a water supply valve near the faucet to turn off the water supply, but if the house is not equipped with a water supply valve for every faucet, you have to turn off the main water supply valve to shut off all water supply.
◆How to use the faucet correctly?
Some citizens like to tighten the faucet every time they run out of water, thinking that this will prevent water leakage. 实际上, the correct use of the faucet should be as light as possible to close and open as much as possible, do not vigorously rotate the faucet knob repeatedly, and should not turn the faucet too tight. 此外, 水龙头应尽量不要撞击硬物. 用于浴缸龙头的使用, 淋浴喷头的金属软管应保持自然拉伸状态. 不使用时请勿将其盘绕在水龙头上. 使用或不使用时, 注意软管与阀体连接处不要形成死角，以免断裂或损坏. 软管.