Different faucet classification and cleaning methods

Faucets are divided into basin faucets, 淋浴龍頭, thermostatic faucets, ETC. The maintenance methods of these different types of faucets are also slightly different.

Basin Faucet

When buying a single-handle basin faucet, you should pay attention to the diameter of the outlet. Except for TOTO basins, most of them are national standard products on the market. Most of GROHE’s basin faucets are hard pipe water inlets, so you should pay attention to the height of the upper nozzle, 35 working points** from the basin down is appropriate. During installation, an angle valve dedicated to Grohe must be selected, 並且角閥必須固定在牆上的冷熱水管上. 當您發現水龍頭上的角閥與水管有距離時, go to your store at the time to purchase a special extension pipe for the GROHE faucet to connect it.

記住, 不得使用其他水管連接, 因為如果水壓很高, 它很容易脫落並漏水, 給您造成損失. 如果進水管太長超過出水管, the part can be cut off according to your needs. 如果角度不合適, you can bend it to the position you need. 記住: Don’t bend to 90 degrees or greater than hard. When installing the basin to drain, please do not forget to purchase the small connector of the faucet (short-circuit the faucet).

淋浴, 浴缸龍頭 (wall hanging)

After you buy a shower, 浴缸, or wall-mounted faucet, you can choose a suitable height to bury the water pipe. The distance between the hot and cold water pipes must reach 15 work points. You must not forget to flush the water pipe before installation to avoid excessive water quality and damage to the faucet. If the elbow between the faucet and the wall joint is too long, you can cut off a part of the 4-point wire. 記住: the 6-point wire connected to the faucet does not seem to be cut randomly.

Concealed shower, 浴缸龍頭

購買暗裝水龍頭後, 水龍頭的閥芯一般是預埋在牆內的. Be sure to pay attention to the thickness of the bathroom wall before embedding. 如果牆太薄, the spool cannot be embedded. Do not remove the plastic protective cover of the valve core easily when embedding, so as not to damage the valve core due to cement and other chores. 另外, 你應該注意上下, 嵌入閥芯時閥芯的左右方向，避免插錯閥芯.

淋浴龍頭

After you install the shower and bathtub faucets, don’t forget the filter in the shower pipe when you need to install the shower. When installing the shower, the water pressure must not be too high, generally 1&mDASh;—3 kg is the best, not more than 5 kg. If the water pressure is too high, the water flow restrictor in the valve core of the faucet can also be opened to reduce the water pressure, which can also achieve the effect of water saving.

恆溫龍頭

Before installing the thermostatic faucet, please check whether the water pipe is hot on the left and cold on the right. Remember not to connect the hot and cold water pipes wrongly to prevent the faucet from not working properly. Gas and solar water heaters cannot use thermostatic faucets because the water pressure is too low. Don’t forget to install the hot and cold water filter when installing the thermostatic faucet.

Daily maintenance

In the process of using the faucet, it is necessary to frequently maintain and clean the scale on the surface of the faucet and the water sand in the spout to protect the chrome layer on the surface of the faucet as bright as new (GROHE special cleaning fluid, special cleaning cloth). Do not use rough towels and cloths to wipe the faucet, so as not to scratch the chrome layer, and do not touch the faucet with acid-alkaline items to avoid destroying its brightness.